{"product_id":"doepfer-a-100lc1v-low-cost-case-48hp-vintage-edition","title":"Doepfer - A-100LC1V: Low Cost Case 48HP Vintage Edition","description":"\u003cp dir=\"ltr\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe A-100LC1 is very similar to the A-100LC3 but offers only 48 HP for installation of modules. A-100LC3 is equipped with the power supply . \u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e The case is made of \u003c\/span\u003e\u003cu data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e raw wood\u003c\/span\u003e\u003c\/u\u003e\u003cspan data-mce-fragment=\"1\"\u003e without laquering. The case can be varnished by the customer in any desired color e.g. by means of a spray can.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e It is also available with \u003c\/span\u003e\u003cb data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eblack coating\u003c\/strong\u003e\u003c\/b\u003e\u003cspan data-mce-fragment=\"1\"\u003e :A-100LC1\u003c\/span\u003e\u003cb data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eV\u003c\/strong\u003e\u003c\/b\u003e\u003c\/p\u003e \u003cp dir=\"ltr\" data-mce-fragment=\"1\"\u003e\u003cu data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eMeasures in mm:\u003c\/span\u003e\u003c\/u\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e outside: approx. 262 (width) x 158 (depth) x 154 (height)\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e inside: 1 x 48 HP (244 mm) x 3 U (one short bus board), useable depth for A-100 modules: approx. 110\/45 mm (measured from inner side of the front panel until end of the pc board of the module), because of the built in power supply the depth is reduced at the right side: \u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/p\u003e \u003cp data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/p\u003e \u003cp dir=\"ltr\" data-mce-fragment=\"1\"\u003e\u003cu data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eQuantity of bus boards:\u003c\/span\u003e\u003c\/u\u003e\u003cspan data-mce-fragment=\"1\"\u003e 1 (short version with 8 module connectors)\u003c\/span\u003e\u003c\/p\u003e \u003cp dir=\"ltr\" data-mce-fragment=\"1\"\u003e\u003cu data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWeight\u003c\/span\u003e\u003c\/u\u003e\u003cspan data-mce-fragment=\"1\"\u003e: about 1.5 kg (without modules, without mains cable)\u003c\/span\u003e\u003c\/p\u003e \u003cp dir=\"ltr\" data-mce-fragment=\"1\"\u003e\u003cu data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eElectrical specifications:\u003c\/span\u003e\u003c\/u\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e mains voltage: 110 ... 240V~ (IEC connector at the rear panel, the mains cable is not included because of the many different versions for different countries)\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e output voltages\/current: +12V\/380mA, -12V\/380mA, +5V\/100mA (the +5V current is taken from the +12V supply, i.e. the sum of the +12V current and the +5V current has to be less than 380mA)\u003c\/span\u003e\u003c\/p\u003e \u003cp dir=\"ltr\" data-mce-fragment=\"1\"\u003e\u003cu data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eImportant note\u003c\/span\u003e\u003c\/u\u003e\u003cspan data-mce-fragment=\"1\"\u003e: the load regulation of the power supply used in the A-100LC1 (A-100SSB) is not as good as the load regulation of the \"big\" A-100 power supplies (A-100PSU2, A-100PSU3 and the power supply of DIY kit #1). That's why we recommend not to use the A-100LC1 with modules which are sensitive to supply voltage changes. In the first place VCOs are affected. If modules with changing loads (especially modules with LEDs) are installed together with VCOs pitch modulations may be the result. The A-100LC1 should be used only with modules which are immune to slight supply voltage changes (typically control modules like ADSR, LFO, random and most of the sound processing modules like VCFs or VCAs). \u003c\/span\u003e\u003c\/p\u003e","brand":"Doepfer","offers":[{"title":"Default Title","offer_id":54725904990549,"sku":null,"price":105.53,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1071\/1872\/3413\/files\/ue0snv6b0w41viixutnm.jpg?v=1787442142","url":"https:\/\/climivor.myshopify.com\/products\/doepfer-a-100lc1v-low-cost-case-48hp-vintage-edition","provider":"CLIMIVOR","version":"1.0","type":"link"}